Cy7c68013a Driver Win7
Hi I am using cypress cy7c68013a-100a and driver cyusb.sys in 'Cypress Suite USB 3.4.6' for win 7 in wlh folder. And change.inf file (my.inf is attached) and build a board according AN15456 in this address When I connect on some PC's running Windows 7, i see 'the device is not recognized' and 'this device connot start(code10)'! I checked my hardware again and again.but i see this error yet * i can't find 'tps3820-33' for reset pin so i use a 100k from reset pin to 3.3v and a 0.1uf to gnd * 'tps3820-33' is my problem?!! Thanks in advance for any help you can offer sam. I am using cypress cy7c68013a-100a and driver cyusb.sys in 'Cypress Suite USB 3.4.6' for win 7 in wlh folder. And change.inf file (my.inf is attached) and build a board according AN15456 in this address When I connect on some PC's running Windows 7, i see 'the device is not recognized' and 'this device connot start(code10)'! * i can't find 'tps3820-33' for reset pin so i use a 100k from reset pin to 3.3v and a 0.1uf to gnd * 'tps3820-33' is my problem?!!
Your problem could be the 100KΩ resistor you are using as a pullup on the RESET pin. Try dropping it down to 10KΩ and swap out the 0.1µF cap for a 1µF cap. The device maybe stuck in reset state. Below is a schematic for a custom development board which may give you some pointers. I would also advise you to post your schematic, there maybe other issues as well.
Released Updated 1-9-2014 New software download to allow usage of Cypress FX2, non LP version. Updated 2-10-2014 Added InitGenericUsb.dll to the Cypress driver software download folder Updated Add picture and pin information for FX2 Mini Board Updated New EEPROM firmware (msa-fw-cb-v33.hex) to support MSA Software Version 118. This page will explain how to add USB Control to the SLIM MSA. At this time, the Cypress software will support Win XP through Win 8. I have verified this conversion with Win XP Pro and Win 7. I am not sure about Win 10. Vandalism Youtube Bot here.
The complete library and driver stack for USB-Serial Bridge Controller devices is available for download at the Cypress. USB-Serial Software Development Kit. I need driver for windows 8 for device cy7c68013a-56pvxc. Is there driver for this device? There is a description of the driver of Windows7 in the following URL. This parameter is used to register the application as a potential target for incoming cy7c68013a driver windows 7 and crack up laughing hand-off for cy7c68013a driver.
The steps to incorporate USB Interface for MSA: 1. Obtain a Cypress development board using the Cypress CY7C68013A chip set. Construct a wiring interface to couple the development board to the MSA's Control Board. Modify the USB Card and SLIM Control Board for pull-up resistors. Modify MSA SLIM Control Board's Line Filters 5. Install the Cypress driver software 6. Updating EEPROM Firmware.
Cypress Development Board There are several styles on the market, but I will use the EZ-USB FX2LP as the model for this discussion. They can be found on E-Bay with price ranges from $15 to $30. My particular board was a donation from Jim Hontoria, W1JGH, so that we could develop the hardware and software. EZ-USB FX2LP (BESTELECS) Dave Robert's V0-4 Board FX2 Mini Board The EZ-USB FX2LP has two jumpers labeled: Bus Pwr--Leave this jumper to allow the computer to supply the +5v required to power the USB card.
EPROM--This jumper is in place during MSA operation. It will be removed during the software installation process, later on this page. Note: the EEPROM must be at least 16Kx8. Typical are the 24LC128 and 24LC256. The 24C128 and 24C256 are fine also. If the Cypress board is used with the new (in work) Python software, no EEPROM is needed.